MANOY® Shaft Seal

Type 281

MANOY® Shaft Seal

Type 286

MANOY® Shaft Seal

Type 291

MANOY® Shaft Seal

Type 296

TECHNICAL DATAS

outer sealing inner sealing outer sealing inner sealing
Motion Motion Motion Motion
rotary, partially static, partially linear rotary, partially static, partially linear rotary, partially static, partially linear rotary, partially static, partially linear
Direction of pressure Direction of pressure Direction of pressure Direction of pressure
unidirectional unidirectional unidirectional unidirectional
Operating pressure (MPa) Operating pressure (MPa) Operating pressure (MPa) Operating pressure (MPa)
20 20 130 130
Rotary speed (m/s) Rotary speed (m/s) Rotary speed (m/s) Rotary speed (m/s)
5 5 5 5
Diameter range (mm) Diameter range (mm) Diameter range (mm) Diameter range (mm)
20 to 2000 10 to 2000 20 to 2000 10 to 2000
Housing Housing Housing Housing
split

split

split

split

Type 281 outer sealing
Motion rotary, partially static, partially linear
Direction of pressure unidirectional
Operating pressure (MPa) 20
Rotary speed (m/s) 5
Diameter range (mm) 20 to 2000
Housing split
Type 286 inner sealing
Motion rotary, partially static, partially linear
Direction of pressure unidirectional
Operating pressure (MPa) 20
Rotary speed (m/s) 5
Diameter range (mm) 10 to 2000
Housing split
Type 291 outer sealing
Motion rotary, partially static, partially linear
Direction of pressure unidirectional
Operating pressure (MPa) 130
Rotary speed (m/s) 5
Diameter range (mm) 20 to 2000
Housing split
Type 296 inner sealing
Motion rotary, partially static, partially linear
Direction of pressure unidirectional
Operating pressure (MPa) 130
Rotary speed (m/s) 5
Diameter range (mm) 10 to 2000
Housing split

APPLICATIONS

  • High pres­sures at rel­at­ively low speed 
  • For flu­ids over a wide vis­cos­ity range and for gases 
  • Rotary uni­ons at high pressure
  • Robot axes 
  • Pipe joints
  • Injec­tion units
  • Rotary actu­at­ors
  • Rotary lift cylinders
  • Valve spindles
  • Swiv­els

CHARACTERISTICS

  • Pres­sure-activ­ated seal energization 
  • Clamp­ing of the flange in the hous­ing pre­vents unwanted rel­at­ive motion
  • Ideal for slow rotary, oscil­lat­ing and hel­ic­al motion 
  • Dry run­ning possible 
  • Low coef­fi­cient of friction
  • Non-sens­it­ive to pres­sure peaks 
  • No chat­ter (stick-slip) at low speed 
  • Does not stick to the mat­ing sur­face after pro­longed shutdown 
  • Avail­able for any dia­met­er up to 2000 mm

TEMPERATURE RANGE

From -54 to +200 °C (tem­por­ar­ily +260 °C)

but depend­ent on the mater­i­al of the seal and the O-ring in each case.

MATERIALS

IDG seal material

  • 82B (water hydraulics)
  • 32B (pneu­mat­ics)
  • 36B

O-ring elast­omer

  • FKM

Spe­cial mater­i­als are used at low temperatures

Mater­i­al descrip­tion and oth­er mater­i­als for wider applic­a­tions FIND OUT MORE >

PV lim­its

Motion: Rotary or oscillating

Rotary and oscil­lat­ing, non-intermittent

 Rotary and oscil­lat­ing, intermittent
6 s motion/2 s standstill

Rotary and oscil­lat­ing, intermittent
2 s motion/6 s stand­still – flat rising
hel­ic­al in 20:1 ratio

 

Flu­id: Water
Tem­per­at­ure: 95 °C max.
Shaft seal mater­i­al: 36B